Tag: ground investigation

  • Building on Made Ground: Foundation Options for UK Builders

    Building on Made Ground: Foundation Options for UK Builders

    Building on made ground is a job where the paperwork matters as much as the concrete. Lenders, warranty providers and building control all want evidence that the ground has been investigated, and more of the sites left for housing are old infill, former yards and backfilled plots. If you build extensions, plots or small developments, you will meet filled ground sooner or later, and the foundation you choose has to suit what is actually under the topsoil, not what you hope is there.

    Made ground is soil, rubble, ash, brick, clay or general fill that has been put there by people rather than laid down naturally. It is variable, often poorly compacted, and it settles unevenly. That uneven settlement is what cracks walls. The short answer on foundations: standard strip footings are only safe on made ground if a ground investigation proves it, otherwise you go deeper to natural strata, or use piles or a ground-improvement method.

    Deep foundation trench cut through mixed fill on a building site, a key step when building on made ground
    Photo by Đậu Photograph on Pexels

    How do you spot made ground before you dig?

    You spot made ground by looking at the site history, the levels and the first trial pits. Old maps, a former quarry, pond, railway cutting or demolished building on the plot are all warning signs. So is a site that sits higher than its neighbours, or a surface that looks level but has brick, ash, glass or plastic turning up in the spoil.

    Don’t trust a single hole. Fill can be four metres deep at one corner and half a metre at the other. That change in depth across a footprint is what causes differential settlement, which does far more harm than even settlement.

    What does a ground investigation report actually tell you?

    A ground investigation report tells you what is under the site, how strong it is, and what it may do to your concrete. Most small jobs get a desk study plus a few trial pits or boreholes. Read these parts first:

    • Ground profile: the logged layers with depths. Look for where made ground stops and natural clay, sand or gravel starts. That depth is your target.
    • Groundwater: whether water was struck, and at what depth. A high water table affects excavations and trench stability.
    • Strength data: hand shear vane results, SPT blow counts or lab tests, and the recommended allowable bearing pressure. Pay attention to which layer that figure applies to.
    • Soil type and shrinkage: clay plasticity and nearby trees affect how deep footings must go.
    • Chemical results: sulphates, pH and contamination. High sulphates mean sulphate-resisting concrete, and contamination can mean specialist handling, gas protection or a remediation condition from the council.

    Finally, read the engineer’s recommendations and caveats. If the report says the made ground is unsuitable to found on, believe it. Arguing with a borehole log is expensive.

    Which foundations are used on filled or disturbed ground?

    The foundations most often specified on filled ground are deepened strips or trench fill to natural ground, piled foundations with ground beams, and raft foundations. Ground improvement is used less often on small jobs. Which one wins depends on fill depth, loads and access.

    Option Typical use Main drawback
    Deepened trench fill Fill up to roughly 2 to 3 m, good ground beneath Lots of concrete and spoil; trench stability
    Piles and ground beams Deep or variable fill, soft ground Rig access and cost; needs engineer design
    Raft Shallow, variable fill with modest loads Only works if the ground can carry it evenly
    Ground improvement Larger sites; compaction or stone columns Specialist contractor, rarely worthwhile on one house

    Deepened trench fill is the usual first answer because any groundworker can do it. Once the depth runs past what is practical or safe, piling is often cheaper than endless concrete. Engineers design piles and rafts, and you should not guess them. If you are unsure when to bring one in, our guide on when a UK builder needs a structural engineer covers it.

    Why does getting it wrong cost so much?

    Getting it wrong is costly because the fix happens after the building is finished. Typical signs are stepped cracks in brickwork, sticking doors, sloping floors and drainage that falls the wrong way. Remedies include underpinning, resin injection or mini-piling, all of which mean access, disruption and a claim on your insurance or warranty. Your reputation takes the hit too.

    Shrinkable clay with trees nearby is a separate but related trap, and NHBC guidance on foundation depths near trees is worth knowing. Mixing made ground with that, and with a bit of rubbish in the fill that rots away, gives you movement for years.

    What should you check on site before you pour?

    Check that the trench bottom is the stratum the engineer expects, not just the depth on the drawing. Building control can only sign off what they see, so have the inspector or engineer look at the formation before concrete goes in. If you hit soft spots, old drains, buried tanks or a change in material, stop and ask. Photograph the trench bottom with a tape in shot.

    Also check drainage runs near foundations, since trench fill often has to be lowered around pipes. Our piece on sub-base materials for groundworks is useful for what goes in above the footings.

    Where to get the right information

    Don’t rely on an old report from a neighbour’s job; it only describes the boreholes that were dug. If a site has a history of filling, commission your own investigation, and if you need to find clients or contractors who want local visibility for that kind of specialist work, a firm like LinkPress can help you get found by them. For the technical side, the British Geological Survey and the Environment Agency publish useful information on geology and contaminated land at gov.uk land contamination guidance.

    Before you quote on any plot with a filled history, ask for the ground investigation report, read the strata log and the recommendations, and price the deeper foundation. A fixed price that assumes standard strips is the one that costs you money.

    Frequently Asked Questions

    What is made ground in construction?

    Made ground is soil or material placed by people rather than formed naturally, such as rubble, ash, brick and mixed fill. It is usually variable and poorly compacted, so it settles unevenly. That makes it unreliable to build standard foundations on without investigation.

    Can you build a house on made ground?

    Yes, but only with foundations designed for it. That usually means taking footings down to natural ground, using piles and ground beams, or a designed raft. A ground investigation should confirm the approach before work starts.

    How deep do foundations need to be on filled ground?

    They need to reach competent natural ground, so the depth varies by site. It could be under two metres or far more. The ground investigation report and engineer’s design set the depth, not a rule of thumb.

    Do I need a ground investigation report for a small extension?

    Not always, but you should get one if the site has signs of fill, a history of previous use or movement in neighbouring buildings. Building control may ask for one. It is cheap compared with underpinning later.